Electronics 101 for Beginners

Electronics 101 is a hands-on course for beginners. The first two lessons are free on this site. Start with voltage, current, and resistance, then explore LEDs, capacitors, transistors, and sensors. Change component values in the interactive circuit simulator and watch the readings update as you experiment.

ELECTRONICS 101Discover · Experiment · Build
Circuit basics0 / 9
01 / 48 · Circuit basics
Preparing the local 3D workbench…
300.0 mA

Drag / WASD to pan · Right-drag / Q E to rotate · Scroll to zoom · Select a part to inspect

SUPPLY3.00 V
CURRENT300.00 mA
OUTPUT3.00 V
TIME0.00 s
Live curve
Calculated outputMarker = current time
ONE QUICK CHECK

What happens to current when the only switch opens?

Workbench details

Continue Electronics 101 on NavSprout

Explore all 48 interactive lessons or try the four-trial Ohm’s law exercise.

Go to NavSprout

Electronics 101 Course Outline

The course follows seven learning paths. Start with circuit basics and Ohm’s law, then work through resistors, LEDs and diodes, capacitors and RC timing, switches and logic, transistors, and sensors. Each lesson opens its own guide and interactive workbench.

Electronics 101 · Circuit basics

9 lessons

Start with a battery, a switch, and a lamp. Trace the closed path, then compare how components share voltage and current in series and parallel. The breadboard and multimeter lessons show where connections are made and where to take measurements. Use Kirchhoff’s laws to check those measurements at a junction and around a loop.

Electronics 101 · Resistors

8 lessons

Read resistor color bands, then use Ohm’s law to predict how a change in resistance affects current. Compare series and parallel networks and see how a potentiometer sets the output of a voltage divider. In the bridge experiment, adjust one resistance until the two midpoint voltages match.

Electronics 101 · LEDs & diodes

5 lessons

Flip an LED to see what polarity changes. Then compare how much voltage different LEDs need and how a series resistor limits the current. Use rectification to see what happens when a diode passes current during only part of an AC cycle, and check how forward voltages add when LEDs share a series path.

Electronics 101 · Capacitors

9 lessons

Watch capacitor voltage rise and fall as charge moves through a resistor. Change the resistance or capacitance and compare the shape and timing of the curves. Then use the same ideas to explain why a reservoir capacitor reduces ripple, how a timing threshold sets a delay, and how a flasher keeps switching.

Electronics 101 · Switches & logic

4 lessons

Compare a push button that returns when released with a slide switch that holds its position. Follow the conducting path through pairs of switches to see how series and parallel wiring implement AND and OR. In the two-way lighting experiment, try changing either switch and trace the path that reaches the lamp.

Electronics 101 · Transistors

6 lessons

Change the base drive and compare it with the current through a transistor’s load. See how the same device can control current, switch a load, or invert a logic signal. Compare NPN and PNP wiring, then try the Darlington experiment to see how two stages let a small input control a larger load current.

Electronics 101 · Sensors

7 lessons

Vary light, temperature, or magnetic field and observe how the sensor’s output changes. Connect a light sensor or thermistor to a voltage divider, then compare that voltage with a threshold to control a lamp or an alarm. Compare a reed switch’s two states with the continuous output of a Hall sensor.

Electronics 101: Your First Three Circuit Experiments

  1. Open and closed circuits — Toggle the switch and compare the lamp and the current reading.
  2. Volts, amps and ohms — Keep resistance fixed, double the voltage, and check your prediction against the ammeter.
  3. RC charging — Adjust the capacitance and compare the charging curve before and after.

Electronics 101 FAQ

What is Electronics 101?

Electronics 101 has 48 browser-based circuit lessons. Try the first two for free here, purchase a course pass, or go to NavSprout for free access.

Where should I start if I’m new to electronics?

Start with Open and closed circuits. Use the switch to see when current flows, then try Volts, amps and ohms to see how voltage and resistance affect current.

Are these circuit simulations exact?

They are analytic teaching models: ideal sources and switches, fixed diode drops, simple BJT gain and saturation, exponential RC behavior, and illustrative sensor curves. They are not a SPICE solver or construction verification.

Do I need hardware or a login?

No hardware or account is needed. The 3D view needs WebGL, while diagrams, controls and static lessons remain available as alternatives. Progress is stored in this browser and can be exported.

Which current direction is shown?

Moving markers represent conventional current, not electron drift. Their motion is illustrative and is not a measurement of charge velocity.

Electronics 101 Simulation Models and References

These lessons use standard lumped-circuit relationships and explicitly simplified component models. Diagrams explain teaching topologies, while the breadboard probe explains socket continuity. The workbench is not a verified physical assembly plan.

OpenStax: resistor networks ↗OpenStax: RC circuits ↗BJT switching reference ↗

Continue Electronics 101

Take the next lesson on NavSprout for free, or unlock the rest of the course here and pick up at the workbench.

Continue on NavSproutAll 48 lessons · opens in a new tabFree

Checkout opens in a new tab with Dodo Payments. Your course pass is saved in this browser.